Monday, 21 December 2020

The XV sidecar - building the rest of the engine (pt.4)

Last time we left off with me hoping that the courier service wouldn't let me down. Well, it was more than a week, so probably some things happened. Even without immediately having all the parts at my disposal there was a lot more that could still be done. 

First was to assemble the rotor and mark out the correct position on the teeth (you basically do this blind).

Then clean out the oil-pickup on my oil-pump (Gears were fine, yet still...) and install it


As the 750 clutch was missing some parts, it was about time to overhaul that one as well. Springs were overly compressed and the clutch disks completely worn.



As the center bolt on v-star cylinders is longer (M6x100mm to be precise), I had to get a set of those

The other thing was to clean the pistons, as unlike last time on Bumblebee, these were in very good condition, except for the oil-scrapers, which had failed prematurely. A bit of spray-on gasket remover softens the baked on carbon and makes it easier to clean.


But these are just the cosmetics, not pointless, but mostly cosmetics. The important part are the ring-grooves. In order to clean them, you need an old set of rings, of which you clip off a piece or two and then scrape the grooves until they are free of carbon buildup.

Before scraping, after just a light brush with a SOFT brass brush.

And after an hour of thorough cleaning. As a result now the rings move freely in their grooves again.

With the pistons good to go, it was time to focus my attention on the heads. In general the ports on these heads need a mild touchup and not much more, at least not for road use.

I am fully aware, that polishing valves is more or less pointless... but they look too good AND it slows down carbon buildup on them. 



In order to reduce the seat pressure, I mix and match harder and softer valve springs in the hope of getting a bit more life out of the rockers. 




I know these are somewhat debated amongst SR/XT-users, but I love swivelhead valve adjusters as the grant much longer life to the valve stems due to the greater contact patch. Downsides? Heavier and at some point the ball will wear down resulting in the adjuster screw touching the valve and thus resulting in the adjuster breaking. (Ask me how I know...)


 

6205-Z single sided, metal-shielded ball bearing instead of the stock ally journal. 

 

Plenty of assembly lube on the cam.

All assembled. The blue line on the bolt means, it's loctited in. If you can't build an engine in a single go, you have to have some signs for yourself which of the jobs have been tackled and which haven't. (Another one would be my habit of painting the alignment dots on the cam-gear with white paint, so I know the corresponding cylinder has been timed up.)

Tapping the spark-plug thread, because there's not a lot like screwing a spark-plug in a freshly cut and oiled thread.

The camchain adjusters needed some attention too. In stock form the v-star adjusters are too short to work in an older Gen1 engine case with the correct tensioner blades. 





The new buttons have a 16mm head diameter, which is 7mm tall (compared to the stock 2mm) and the bit that goes into the tensioner is 8.6 in diameter and you can basically make it as long as you like, but I went with 6mm. Material was slightly better grade mild-steel (St.52), because that's what I had on hand and it machines lovely.


As I plan to run VM38 carbs on the sidecar and the VM38-200 inlet rubbers don't have any provision for vacuum ports I installed them right in the cylinder heads. The tubing used is 6mm ally tube with 1mm wall-thickness.





And one last tip: if you ever want to use your oil-filler cap again, you will have to trim the bottom most cooling fin of the front cylinder. 


And there you have it: a XV and XVS1100 hybrid.

Not going as far as to say it's ready to be bolted in, but it's quite a bit closer now.

Wednesday, 9 December 2020

The XV sidecar - building (most of) the engine (pt.3)

The engine for the new sidecar is by no means radical or anything out of the ordinary. Much the contrary, it was the recipe that I came up with for the bumblebee engine, which originally inspired me to reconsider building a XV-based sidecar. 

The basis for the engine as such will be a set of XV1100 cases, which are a straight fit into my Gen1 XV750 frame, in order to accept BT1100 cylinders the crankcase mouths have to be enlarged ever so slightly (0.5mm on the diameter to be precise). 

The crank is a (once more) a wild mix of a heavy (12kg) XV1100 crank with BT1100 connecting rods and pistons. Crank is a #3 and conrods #5, so black bearing shells was what the factory manual called for.

Even though it makes starting quite a bit more difficult, but the red assembly lube is instrumental in protecting the bearing shells until oil-pressure has built up.


On the TR1-engine I used a holesaw to modify the case mouths, this time I went with a die-grinder and a flap-wheel. Not only was it A LOT quicker, I didn't attempt to break my wrist this time, which I consider a huge plus.

I am not one big into vanity-mods, but I admit I like my XV-engines in all silver.


 Originally I borrowed one of the long studs from these XV1100 cases and used them on my TR1-engine. Now it was time to take one from the XV750 engine that came with the other parts. 


Also XV1100s don't appear to have this one stud on the right side of the engine.

One of the very minor differences between XV750 and 1100 cases: The later cases lack the boss, which I love to use for the oil-pressure sensor. Guess, I'll have to figure out something along the way. 


Aside from the rotating assembly, I planned to use quite a few bits from the original XV750 donor engine as it must have been overhauled only shortly before it failed (because of an incorrect check bolt in the oilfilter-cover preventing any oil-pressure to the head from building up and killing cams and rockers.)

On the subject of failures: When they pulled the crank the first time, the thread on the crank-end got mushroomed slightly and thus the rotor was only on handtight (at best). 


Also the oil-seal in the clutch cover was damaged leading to even less oil-pressure... 



The left side crankshaft bearing had been removed in the past (most likely because I needed for a TR1 engine and now a good used bearing was installed - we'll see how that fares.) As it was just slightly above freezing in my workshop, the bearing install was rather straight forward.


The crank-install on the other side fought me all the way this time. 

With my penchant for ratty mostly black bikes, it might be a bit surprising to some, what I actually have a rather well stacked box with all sorts of polishing mops and the like. To be fair, I hardly ever use it on parts one can see. In this particular case, I polished the guide-rod for the shifter forks. One of those little jobs which helps with silky smooth shifts later on.

With the gearbox installed it was just a matter of bolting the two halves together and calling it an engine. As one of the dowels fell out, it gave me the opportunity to take a picture of just how far you get with a 1 to 1.5mm wide bead of engine silicone.


If the courier-service doesn't let me down, I should have all the missing parts by the end of the week and be able to finish the engine next weekend.

Monday, 30 November 2020

The XV sidecar - taking inventory (pt.2)

Now if you do a project on a budget, there's inherently going to be some compromises or extra work you have to do. In my case some of the metal stuff was incredibly rusty. 




More importantly the lower frame section that came with the bike had the swingarm completely seized on the pivot bolt and the bolt head was already decently rounded off. 

Luckily getting the actual final drive off proved to be rather easy with no seized fasteners or the like.

One of the central elements in this project is the usage of XS-Triple wheels. Now I had seen some pictures of one guy fitting a rear wheel into a XV750, but that was it. Turns out the coupling is the same diameter and tooth-count but so far I am not sure if they fully engage.

The only thing necessary to make the splines engage was to remove the dustshield on the XS-rear-wheel, but I think for practical use, I will space the coupling out by a few mm to a) improve engagement and b) allow for a bit more clearance to the shaft.


Next step will be to build as much of the engine as possible to empty out the XV750 engine that came with the bike in order to make it easier to handle. (I already know that I will be waiting a while for some of the parts, but I don't want that to stop me from building the exhaust, subframe, etc...)